![]() |
Matte/Gloss Black UB3 Lid for Micromite LCD BackPack V3 using 3.5in screen A lid laser cut from 3mm black acrylic which replaces the lid supplied with a UB3 "Jiffy" box. Attaches with the supplied screws. One side is gloss black, the other side is matte black. You can fit it either way around. Unlike the lids designed for the 2.8in screens, this one recesses within the Jiffy box, giving a slightly more compact result.
| |||||||||||||
![]() |
Colour Maximite 2 front & rear panels The pair of front and rear panels for the Colour Maximite 2 computer. Each panel is made from a 1.6mm-thick PCB with black solder mask and white silkscreen printing. All holes and cut-outs are pre-made. Both panels are 135 x 30.75 x 1.6mm. These are designed to slot into the plastic instrument case specified in the parts list, replacing the plastic panels that come with it.
| |||||||||||||
![]() |
Ol' Timer II laser-cut case pieces and spacer A set of 3mm black laser-cut acrylic case pieces and the LED array spacer required to build the Ol' Timer II word clock. Note: the screws shown in the photo are not included and must be purchased separately.
| |||||||||||||
![]() |
Case pieces for the Super-9 Stereo FM Radio A set of six laser-cut 3mm acrylic case pieces for the Super-9 Stereo FM Radio. The set includes the front, top, bottom and side panels in gloss black and the transparent rear panel and handspan dial. The hardware to hold them together is not included. See the article in the December 2019 issue for assembly instructions.
| |||||||||||||
![]() |
3mm acrylic heatsink spacer for High-power Linear Bench Supply A 3mm thick plastic spacer, designed to go under the Bench Supply heatsink and insulate it from the case, while still providing secure mounting and also allowing good airflow through the bottom of the fins.
| |||||||||||||
![]() |
3mm acrylic bezel for the Digital Panel Meter A laser-cut black acrylic bezel to suit a typical 16x2 alphanumeric LCD module, as used in the Five-way Panel Meter project.
| |||||||||||||
![]() |
Laser-cut acrylic case pieces for the GPS "Finesaver Plus" Speedo/Clock/Volume Control A set of four matte black 3mm laser-cut acrylic case pieces for the PCB for the GPS Speedometer/Clock/Volume Control project. See the article for construction details.
| |||||||||||||
![]() |
Matte Black UB3 Lid for the Multi Diode Curve Plotter A lid laser cut from 3mm black acrylic which replaces the lid supplied with a UB3 "Jiffy" box. The side facing outwards is matte black. The Diode Curve Plotter assembly is mounted on the rear of the lid using four M3 machine screws, with the touch-screen flush with the top surface. The cut-out is sized to leave minimal clearance around the screen. 120 x 62mm. Note: for the lid to fit, the LCD pin header solder joints (top side) must be trimmed. Use two M3 washers (or one 1mm thick Nylon washer) as spacers between the TFT PCB and the lid.
| |||||||||||||
![]() |
Case pieces for the DAB+/FM/AM Tuner A set of transparent 3mm laser cut acrylic case pieces for the DAB+/FM/AM Tuner. Note: photo shows fully assembled radio inside assembled case.
| |||||||||||||
![]() |
Case pieces for the Wide-range Digital LC Meter A set of six laser-cut 3mm clear acrylic case pieces for the Low-drift, Wide-range LC Meter. The front panel now includes laser-etched labels.
| |||||||||||||
![]() |
Case pieces for the Super-7 AM Radio A set of six laser-cut 3mm acrylic case pieces for the Super-7 Superhet AM Radio. The set includes the front, top, bottom and side panels in gloss black and the transparent rear panel and handspan dial. The hardware to hold them together is not included. See the article in the December 2017 issue for assembly instructions.
| |||||||||||||
![]() |
Case pieces for the 6GHz+ Frequency Counter A set of transparent 3mm laser cut acrylic case pieces for the 6GHz+ Frequency Counter.
| |||||||||||||
![]() |
Black acrylic case pieces for the 3-Way Adjustable Stereo Active Crossover for Loudspeakers Top, bottom and side case pieces for the 3-way Active Crossover, cut from 3mm black acrylic. With the front and rear panels, these form the case for the Crossover. The case can be assembled so that the outside surface is either matte black (recommended) or gloss black. The article in the October 2017 issue has the full case assembly details. Total panel size: 223 x 302 x 3mm.
| |||||||||||||
![]() |
Front & rear panels for the 3-Way Adjustable Stereo Active Crossover [01108172/3] Front and rear panels for the 3-Way Fully Adjustable Stereo Active Crossover for Loudspeakers. Each panel is made from a 1.6mm-thick PCB with black solder mask and white silkscreen printing. All holes and cut-outs are pre-made. The front panel is 296 x 43mm and coded 01108172. The rear panel is also 296 x 43mm and coded 01108173. Sold as a pair. These are designed to slot into the set of four black acrylic case pieces and form a complete case (sold separately).
| |||||||||||||
![]() |
Matte Black UB1 Lid for the Deluxe Touchscreen eFuse A lid laser cut from 3mm black acrylic which replaces the lid supplied with a UB1 "Jiffy" box. Attaches with the supplied screws (longer self-tapping screws may be required, depending on what comes with the box). The external side can be either matte or gloss black. The Deluxe eFuse PCB is mounted on the rear of the lid using four M3 machine screws, with the touch-screen flush with the top surface. The cut-out is sized to leave minimal clearance around the screen. There are also profiled holes to mount the six binding posts. 158 x 96.5mm. Note: after removing the protective film, you may need to clean off some glue residue using a damp cloth.
| |||||||||||||
![]() |
Matte/Gloss Black UB3 Lid for 2.8-inch Micromite LCD BackPack A lid laser cut from 3mm black acrylic which replaces the lid supplied with a UB3 "Jiffy" box. Attaches with the supplied screws. One side is gloss black, the other side is matte black. You can fit it either way around. The 2.8-inch Micromite LCD BackPack is mounted on the rear of the lid using four M3 machine screws, with the touch-screen flush with the top surface. The cut-out is sized to leave minimal clearance around the screen. The cut-out and mounting holes are positioned so that the viewable area of the TFT display is centred. This lid can also be used with the Micromite Plus LCD BackPack. 130.5 x 68.2mm. Note: for the lid to fit, the LCD pin header solder joints (top side) must be trimmed. Use two M3 washers (or one 1mm thick Nylon washer) as spacers between the TFT PCB and the lid.
| |||||||||||||
![]() |
Clear UB3 Lid for 2.8-inch Micromite LCD BackPack A lid laser cut from 3mm clear acrylic which replaces the lid supplied with a UB3 "Jiffy" box. Attaches with the supplied screws. The 2.8-inch Micromite LCD BackPack is mounted on the rear of the lid using four M3 machine screws, with the touch-screen flush with the top surface. The cut-out is sized to leave minimal clearance around the screen. The cut-out and mounting holes are positioned so that the viewable area of the TFT display is centred. This lid can also be used with the Micromite Plus LCD BackPack. 130.5 x 68.2mm. Note: for the lid to fit, the LCD pin header solder joints (top side) must be trimmed. Use two M3 washers (or one 1mm thick Nylon washer) as spacers between the TFT PCB and the lid.
| |||||||||||||
![]() |
Gloss Black UB3 Lid for 2.8-inch Micromite LCD BackPack A lid laser cut from 3mm gloss black acrylic which replaces the lid supplied with a UB3 "Jiffy" box. Attaches with the supplied screws. The 2.8-inch Micromite LCD BackPack is mounted on the rear of the lid using four M3 machine screws, with the touch-screen flush with the top surface. The cut-out is sized to leave minimal clearance around the screen. The cut-out and mounting holes are positioned so that the viewable area of the TFT display is centred. This lid can also be used with the Micromite Plus LCD BackPack. 130.5 x 68.2mm. Note: for the lid to fit, the LCD pin header solder joints (top side) must be trimmed. Use two M3 washers (or one 1mm thick Nylon washer) as spacers between the TFT PCB and the lid.
| |||||||||||||
![]() |
Rapidbrake alignment jig pieces A set of pieces laser-cut from 3mm acrylic which can be assembled to form a jig to help with the RapidBrake alignment process. For more details, see the article in the August 2017 issue, from page 84 onwards. 143 x 98 x 3mm.
| |||||||||||||
![]() |
Front panel for the 10-Octave Stereo Graphic Equaliser [01105172] RevB Front panels for the High-performance 10-Octave Stereo Graphic Equaliser. Made from a 1.6mm-thick PCB with black solder mask and white silkscreen printing. All holes and cut-outs are pre-made. Can be used in combination with, or separately from, the laser-cut black acrylic case. Note that this panel is slightly larger than the version originally published (which was the same size as the main PCB), so that it totally covers the plastic case for a better appearance. 212 x 89mm.
| |||||||||||||
![]() |
10-Octave Stereo Graphic Equaliser acrylic case pieces 3mm thick black acrylic case pieces for the High-performance 10-Octave Stereo Grahpic Equaliser. Six pieces are included which make up the case, as per the articles in the June and July 2017 issues. The exterior surface is matte, to resist fingerprints and scuffing.
| |||||||||||||
![]() |
Clear UB3 Lid for Arduino-based Digital LC Meter A lid laser cut from 3mm clear acrylic which replaces the lid supplied with a UB3 "Jiffy" box. Attaches with the supplied screws. See the article for more details. 130.5 x 68.2mm.
| |||||||||||||
![]() |
Translucent blue UB1 lid for the All-new Swimming Pool Lap Counter A lid laser cut from 3mm translucent blue acrylic which replaces the lid supplied with a UB1 "Jiffy" box. Attaches with the supplied screws (longer self-tapping screws may be required, depending on what comes with the box). The LED display is visible through the lid and provides some basic protection for the internals from small splashes (although it's certainly not waterproof unless you silicone it in place). 152 x 90mm.
| |||||||||||||
![]() |
Matte Black UB1 Lid for the Precision Voltage & Current Reference with Touchscreen Control A lid laser cut from 3mm black acrylic which replaces the lid supplied with a UB1 "Jiffy" box. Attaches with the supplied screws (longer self-tapping screws may be required, depending on what comes with the box). The external side is matte black. The 2.8-inch Micromite LCD BackPack is mounted on the rear of the lid using four M3 machine screws, with the touch-screen flush with the top surface. The cut-out is sized to leave minimal clearance around the screen. There are also profiled holes to mount the four binding posts. 158 x 96.5mm. Note: after removing the protective film, you may need to clean off some glue residue using a damp cloth.
| |||||||||||||
![]() |
Translucent Blue UB1 Lid for the Precision Voltage & Current Reference with Touchscreen Control A lid laser cut from 3mm blue acrylic which replaces the lid supplied with a UB1 "Jiffy" box. Attaches with the supplied screws (longer self-tapping screws may be required, depending on what comes with the box). The 2.8-inch Micromite LCD BackPack is mounted on the rear of the lid using four M3 machine screws, with the touch-screen flush with the top surface. The cut-out is sized to leave minimal clearance around the screen. There are also profiled holes to mount the four binding posts. 158 x 96.5mm.
| |||||||||||||
![]() |
Matte/Gloss Black UB5 Lid for Passive Phono To Line Input Converter A lid laser cut from 3mm black acrylic which replaces the lid supplied with a UB5 "Jiffy" box. Attaches with the supplied screws (note: in some cases you may need to use longer self-tapping screws than those supplied with the original box). One side is gloss black, the other side is matte black. You can fit it either way around. The Phono To Line Input Converter board attaches using a single black, self-tapping screw or an M2 machine screw and nut. Holes are provided for the four RCA sockets along with this mounting screw, and for the four screws to attach the lid to the box. 130.5 x 68.2mm.
| |||||||||||||
![]() |
Matte Black UB1 Lid for the Touchscreen Appliance Energy Meter A lid laser cut from 3mm black acrylic which replaces the lid supplied with a UB1 "Jiffy" box. Attaches with the supplied screws (longer self-tapping screws may be required, depending on what comes with the box). The external side is matte black. The 2.8-inch Micromite LCD BackPack is mounted on the rear of the lid using four M3 machine screws, with the touch-screen flush with the top surface. The cut-out is sized to leave minimal clearance around the screen. 158 x 96.5mm. Note: after removing the protective film, you may need to clean off some glue residue using a damp cloth.
| |||||||||||||
![]() |
Front & rear panels for the Currawong 2 x 10W Stereo Valve Amplifier [01111142/3] Front and rear panels for the Currawong Stereo Valve Amplifier. Each panel is made from a 1.6mm-thick PCB with black solder mask and white silkscreen printing. All holes and cut-outs are pre-made and the corners are rounded. The front panel is 249 x 30mm and coded 01111142. The rear panel is 249 x 53.5mm and coded 0111143. Sold as a pair.
| |||||||||||||
![]() |
Currawong 2 x 10W Stereo Valve Amplifier acrylic top cover 3mm thick clear acrylic top cover for the Currawong. Thirteen separate pieces are provided, all accurately laser cut:
290 x 286mm total size.
| |||||||||||||
![]() |
Matte Black UB3 Lid for Compact 8-digit Frequency Meter A lid laser cut from 3mm black acrylic which replaces the lid supplied with a UB3 "Jiffy" box. Attaches with the supplied screws. The exterior surface is matte black, to match a black jiffy box. The Compact 8-digit Auto-Ranging Frequency Meter PCB is mounted on the rear of the lid using four M3 machine screws, with the LCD screen flush with the top surface. The cut-out is sized to leave minimal clearance around the screen. For best appearance, use two 1mm-thick Nylon washers under each LCD mounting spacer and use a full-depth female header to plug in the LCD. This ensures that the top of the LCD is flush with the top of the lid. Note: after removing the protective film, you may need to clean off some glue residue using a damp cloth. 130 x 68mm.
| |||||||||||||
![]() |
Stereo LED Audio Level Meter / VU Meter clear acrylic case pieces 3mm thick clear acrylic case pieces for the 100dB Stereo LED Audio Level/VU Meter design. Six large pieces and three small pieces are provided, all accurately laser cut. Use acrylic glue and machine screws to complete the case as per the articles. 210 x 190mm total size. Note: PCB and parts shown in image not included (available separately).
| |||||||||||||
![]() |
Hifi Stereo Valve Preamplifier clear acrylic case pieces 3mm thick clear acrylic case pieces for the Hifi Stereo Valve Preamplifier design. Six pieces are provided, all accurately laser cut. Use acrylic glue and self-tapping screws to complete the case as per the articles. 325 x 310mm total size.
| |||||||||||||
![]() |
High Visibility 6-Digit LED GPS Clock acrylic case pieces - CLEAR 3mm thick clear acrylic case pieces for the GPS-Enabled Six Digit LED Clock. Six large and six small pieces are provided, all accurately laser cut. Use acrylic glue and self-tapping screws to complete the case as per the articles. These pieces are clear so suit any colour LED displays. 341.5 x 216mm total size.
| |||||||||||||
![]() |
High Visibility 6-Digit LED GPS Clock acrylic case pieces - BLUE TINTED 3mm thick translucent blue acrylic case pieces for the GPS-Enabled Six Digit LED Clock. Six large and six small pieces are provided, all accurately laser cut. Use acrylic glue and self-tapping screws to complete the case as per the articles. These pieces are blue so suit only blue LED displays. 341.5 x 216mm total size.
| |||||||||||||
![]() |
High Visibility 6-Digit LED GPS Clock acrylic case pieces - GREEN TINTED 3mm thick translucent green acrylic case pieces for the GPS-Enabled Six Digit LED Clock. Six large and six small pieces are provided, all accurately laser cut. Use acrylic glue and self-tapping screws to complete the case as per the articles. These pieces are green so suit only green LED displays. "Emerand green" displays are recommended due to their higher brightness & efficiency. 341.5 x 216mm total size.
| |||||||||||||
![]() |
High Visibility 6-Digit LED GPS Clock acrylic case pieces - RED TINTED 3mm thick translucent red acrylic case pieces for the GPS-Enabled Six Digit LED Clock. Six large and six small pieces are provided, all accurately laser cut. Use acrylic glue and self-tapping screws to complete the case as per the articles. These pieces are red so suit only red LED displays. 341.5 x 216mm total size.
| |||||||||||||
![]() |
Calibrated Turntable Strobe Disc [04101162] This disc is placed over the spingle on a record turntable and allows the speed to be adjusted or checked accurately for 33⅓, 45 and 78RPM discs. Used in combination with our White LED Turntable Strobe unit. Bands are provided for 33⅓ and 45RPM for a 120Hz strobe and 78RPM for both 100Hz and 120Hz strobes. Made from black PCB material with silver markings and white text. 100 x 100mm.
| |||||||||||||
![]() |
Appliance Earth Leakage Tester front panel [04203153] Front panel for the Earth Leakage Tester. Made from PCB material with a blue solder mask and white silkscreen printing with all required holes routed out. 89 x 151mm.
| |||||||||||||
![]() |
Balanced Input Attenuator front and rear panels [04105152/3] Front and rear panels for the Balanced Input Attenuator for Audio Analysers and Scopes, coded 04105152 and 04105153 respectively. Made from PCB material with a red solder mask and white silkscreen printing with all required holes routed out. These replace the front and rear panels of the case. Both sides are covered with a copper layer under the solder mask with an exposed area at the rear to make contact with the main body of the case, for electromagnetic shielding. 170 x 53.5mm each.
| |||||||||||||
![]() |
Appliance Insulation Tester front panel [04103152] Front panel for the Appliance Insulation Tester. Made from PCB material with a blue solder mask and white silkscreen printing with all required holes routed out. 89 x 151mm.
| |||||||||||||
![]() |
Remote Switching Programmable Mains Timer panel/lid [19112142] Lid/panel for the Programmable Mains Timer With Remote Switching. This replaces the plastic lid of the UB1 jiffybox, as shown in the article. Made from PCB material (copper clad fibreglass laminate) with blue solder mask, white printing and all cut-outs already made. 157.5 x 94mm.
| |||||||||||||
![]() |
Nirvana Valve Sound Simulator front panel [01106142] Front panel for the "Nirvana" Valve Sound Simulator. Made from PCB material with a blue solder mask and white silkscreen printing. Holes for LEDs, pots and switches are pre-made (routed/drilled). Fits into the integral slots on the case. The rear panel simply requires three holes drilled into the plastic panel supplied with the case. 135 x 30mm.
| |||||||||||||
![]() |
2.5GHz 12-Digit Frequency Counter front panel [04111123] Front panel for the High-Resolution 2.5GHz 12-Digit Frequency Counter project. (May also be referred to as a Frequency Meter). Made from PCB material with a black solder mask and white silkscreen printing. Large rectangular cut-out for LED display and holes for LEDs, buttons and mounting screws are pre-made (routed/drilled). Note that you may need to enlarge the holes for the power switch and input connectors, which can be done easily with a tapered reamer. 248 x 75mm, 2mm thick.
| |||||||||||||
![]() |
Li'l Pulser Mk2 front & rear panels [09107132/3] Front and rear panels for the Li'l Pulser Mk.2 model train controller. Sold as a set. Both are PCBs with a blue solder mask with white printing. The holes are pre-drilled and the rear panel has exposed copper to mount the two power Mosfet devices plus vias to help with heat dissipation. 134.5 x 30mm each.
| |||||||||||||
![]() |
SiDRADIO front & rear panels [06109132/3] Front and rear panels for the SiDRADIO self-contained SDR. Sold as a set. Both are made from PCB material with a red solder mask and white printing. Being PCBs, they also provide some shielding. 218.5 x 34mm each.
| |||||||||||||
![]() |
CLASSiC DAC front & rear panels [01102132/3] Front and rear panels for the High-Performance CLASSiC DAC. Sold as a set. Both are PCBs; the front panel hosts some circuitry on the back while the rear panel is purely a dress piece. Both have a blue solder mask with white printing. Being PCBs, they also provide some shielding. 218.5 x 34mm each.
| |||||||||||||
![]() |
LED Musicolour front & rear panels [16110122/16110123] Front & Rear panels for the LED Musicolour. Manufactured as PCBs with white silkscreening on red solder mask and routed cut-outs for connectors. Sold as a set. 134.5 x 30mm each.
| |||||||||||||
![]() |
USB Virtual Instrument Interface front panel [24109122] Front panel for the USB Virtual Instrument Interface ("Virtins"). This front panel is attached on top of the existing case lid and provides a decorative facade and labels for the controls, inputs and outputs. Made from thin PCB material (0.8mm fibreglass) with pre-cut holes and white silkscreened on blue solder mask. 168 x 117mm.
| |||||||||||||
![]() |
Capacitance Decade Box panel/lid [04106122] Panel/Lid for the Capacitance Decade Box. Made from PCB material (fibreglass). Replaces the existing Jiffy Box lid. With pre-drilled holes and white silkscreened labelling on blue solder mask. 157.5 x 95mm.
| |||||||||||||
![]() |
High Temperature Thermometer/Thermostat front & rear panels [21105122/3] Front and rear panels for the High Temperature Thermometer/Thermostat. Manufactured as PCBs with white silkscreening on red solder mask and routed cut-outs for connectors, controls and display. Sold as a set. 134.5 x 30mm each.
| |||||||||||||
![]() |
SemTest front panel [04103123] Front panel for the SemTest. This front panel is attached on top of the existing case lid and provides a decorative facade and labels for the controls, power and connections. Made from PCB material (fibreglass) with pre-cut holes and white silkscreened on blue solder mask. 230 x 134mm.
| |||||||||||||
![]() |
Resistance Decade Box panel/lid [04104122] Panel/Lid for the Resistance Decade Box. Made from PCB material (fibreglass). Replaces the existing Jiffy Box lid. With pre-drilled holes and white silkscreened labelling on blue solder mask. 157.5 x 95mm.
| |||||||||||||
![]() |
Stereo Audio Compressor front & rear panels [0120112P1/2] Front and rear panels for the Stereo Audio Compressor. Manufactured as PCBs with white silkscreening on red solder mask and routed cut-outs for connectors, controls and display. Sold as a set. 134.5 x 30mm each.
| |||||||||||||
![]() |
Digital Audio Delay front & rear panels [01212112/3] Set of Front & Rear Panels for the Digital Audio Delay.
|