 |
Pico Gamer kit without case or battery
A kit that includes the Pico Gamer PCB, LCD touchscreen, pre-programmed RP2040+ module and almost all the other bits you need.
The only things you need to add are a LiPo battery (cell) and the case. The photo shows the assembled PCB.
|
 |
Pico Gamer kit with white case, no battery
A kit that includes the Pico Gamer PCB, LCD touchscreen, pre-programmed RP2040+ module, 3D-printed case and almost all the other bits you need.
The 3D-printed case is made using the LEDO6060 white resin. You can use it as-is but it might yellow slightly over time. To avoid that, you can paint it any colour you like.
The only thing you need to add is a LiPo battery (cell). The photo shows the case with the assembled PCB.
|
 |
Pico Gamer kit with dark grey case, no battery
A kit that includes the Pico Gamer PCB, LCD touchscreen, pre-programmed RP2040+ module, 3D-printed case and almost all the other bits you need.
The 3D-printed case is made using black resin (very dark grey in reality). You can use it as-is; it shouldn't need painting, and should be somewhat more robust than the LEDO6060 resin (more tolerant to high temperatures etc). You could still paint it if you want to.
The only thing you need to add is a LiPo battery (cell). The photo shows the case with the assembled PCB.
|
 |
ESP32-CAM LCD BackPack short-form kit
A kit for the ESP32-CAM BackPack that includes the PCB, 3.5in LCD touchscreen, CP2102 USB/serial adaptor and other bits and pieces you need to build it.
The only thing not included is the ESP32-CAM module itself, which you can get from various vendors like Altronics.
The photo shows the partially assembled PCB, before the touchscreen and ESP32-CAM module are attached.
|
 |
Short-form kit for the Calibrated Microphone (SMD version)
A kit that includes the PCB and all SMD components to build the main circuit board for the Calibrated Measurement Microphone. Suitable electret microphone capsules (ECMs) are available separately and those sets also include the required compensation components.
All that's left is the XLR socket, wire and housing. There are two options for the housing, as described in the article.
Note: photo shows assembled module. Some components may have a different appearance.
|
 |
Short-form kit for the Calibrated Microphone (TH version)
A kit that includes the PCB and all through-hole components to build the main circuit board for the Calibrated Measurement Microphone. Suitable electret microphone capsules (ECMs) are available separately and those sets also include the required compensation components.
All that's left is the XLR socket, wire and housing. There are two options for the housing, as described in the article.
Note: photo shows assembled module. Some components may have a different appearance.
|
 |
Digital Video Terminal kit
A short-form kit that Includes everything needed to build the Pico Digital Video Terminal except the case (which is available from Altronics).
The Raspberry Pi Picos in the kit are not programmed. They can be programmed easily using a micro USB cable and a computer, as described in the article.
See the link immediately below for a full list of what's included in the kit.
There are two cases that can be used so make sure you select the correct front panel when you order the kit, so suit the case you'll be using.
Note: photo shows assembled kit.
|
 |
Mains Power-Up Sequencer hard-to-get parts
This set of parts includes the critical components needed to build the Mains Power-Up Sequencer: the PCB, the programmed microcontroller, all other semiconductors and the insulating LED bezels.
There are quite a few other parts required, but they are all standard types that should be available from your usual electronics retailer.
Click the link immediately below for a full list of all parts included in this set.
Note: photo shows fully assembled PCB, including parts not included in this set.
|
 |
Mains Power-Up Sequencer Current Detection add-on hard-to-get parts
This set includes a few extra parts needed to add the Current Detection feature to the Mains Power-Up Sequencer.
Click the link immediately below for a list of parts included in this set.
|
 |
Microphone Preamplifier short-form kit
A kit that includes the Mic Preamp PCB and all the parts that mount on it. As a bonus, it also includes the switches and the mounting hardware. Add a case, XLR connectors, bezel LED and wiring and you have a complete preamp.
Click the link immediately below for a full list of the parts included in the kit.
|
 |
USB Keyboard Adaptor for VGA PicoMite short-form kit
A kit that includes the PCB and all onboard parts for the USB Keyboard Adaptor. It can either be built into a VGA PicoMite or into a Jiffy box as a standalone converter (box not included in kit).
Click the link below or see the parts list in the article for a list of everything that's included in the kit.
Note: photo shows assembled kit.
|
 |
ps2x2pico PS/2 Adaptor kit
A kit that includes the PCB and all onboard parts for the ps2x2pico version of the USB Keyboard Adaptor. This is the version that can handle a PS/2 keyboard and mouse, and it can be built into a Jiffy box (box not included in kit).
Click the link below or see the parts list in the article for a list of everything that's included in the kit.
Note: photo shows assembled kit.
|
 |
Secure Remote Switch receiver short-form kit
A kit that includes most of the parts needed to build the Secure Remote Switch receiver, including the PCB and most onboard parts. You just need to add the case, 433.9MHz receiver module RX1 and switches S1 & S5.
All the parts needed to run off 12V or 24V DC are included but please make sure to choose the correct relay voltage from the options below when ordering.
See the link below for details on everything included in this kit.
Note: the photo shows the assembled board, ready to install in its case.
|
 |
Secure Remote Switch transmitter short-form kit (module version)
A kit that includes most of the parts to build the Secure Remote Switch transmitter, including the PCB, components, case and label (sticker). You just need to add the 433.9MHz transmitter module and battery.
See the link below for details on everything included in this kit.
Note: the photo shows the assembled board in the case with the lid removed. Battery not included.
|
 |
Secure Remote Switch transmitter complete kit (discrete version)
A kit that includes virtually all the parts to build the Secure Remote Switch transmitter, including the PCB, components, case and label (sticker). You just need to add the battery.
See the link below for details on everything included in this kit.
Note: the photo shows the assembled board in the case with the lid removed. Battery not included.
|
 |
Multi-channel Volume Control control module kit
A kit that includes all the parts needed to build the control and power supply module for the Multi-Channel Volume Control, including the LCD touchscreen. You can connect up to five Volume Control modules to this to control the level of up to 20 audio channels (16 if an OLED Module is included).
See the link below for details on everything included in this kit. A 1m length of ribbon cable is included to connect the various modules in the system.
You will also need at least one Volume Control module. That kit is available separately, as is the optional OLED Module.
Note: the photo shows the fully assembled module.
|
 |
Multi-channel Volume Control volume module kit
A kit that includes all the parts needed to build one four-channel volume control module for the Multi-Channel Volume Control. Up to five of these modules (20 channels) can be used together, or four (16 channels) if an OLED Module is included.
See the link below for details on everything included in this kit.
You will also need a Control module, which also provides power to this module. That kit is available separately.
Note: the photo shows the fully assembled module.
|
 |
Multi-channel Volume Control OLED module kit
A kit that includes all the parts needed to build the optional OLED and control module for the Multi-Channel Volume Control, including the OLED screen and bezel (which is also the circuit board).
See the link below for details on everything included in this kit.
You still need the Control Module that powers all these other boards (kit available separately), and with this module, you are limited to controlling the volume of 16 audio channels (with four Volume Modules).
Note: the photo shows the fully assembled module.
|
 |
Ideal Bridge Rectifier kit, 28mm spade version
A complete kit to build one Ideal Bridge Rectifier in the 28mm square form factor with blade connectors.
For a complete list of parts in the kit, see the link below.
Note that to generate split rails like in an audio amplifier, you need two Ideal Bridge Rectifiers and a transformer with two separate secondary windings (not a common centre tap connection).
The photo shows the fully-assembled module.
|
 |
Ideal Bridge Rectifier kit, 21mm square PCB pin version
A complete kit to build one Ideal Bridge Rectifier in the 21mm square form factor with pin (wire lead) connectors.
For a complete list of parts in the kit, see the link below.
Note that to generate split rails like in an audio amplifier, you need two Ideal Bridge Rectifiers and a transformer with two separate secondary windings (not a common centre tap connection).
The photo shows the fully-assembled module.
|
 |
Ideal Bridge Rectifier kit, 5mm pitch SIL version
A complete kit to build one Ideal Bridge Rectifier in the 5mm pitch SIL form factor with pin (wire lead) connectors.
For a complete list of parts in the kit, see the link below.
Note that to generate split rails like in an audio amplifier, you need two Ideal Bridge Rectifiers and a transformer with two separate secondary windings (not a common centre tap connection).
The photo shows the fully-assembled module.
|
 |
Ideal Bridge Rectifier kit, mini SOT-23 version
A complete kit to build one Ideal Bridge Rectifier in the mini SOT-2 form factor with pin (wire lead) connectors.
For a complete list of parts in the kit, see the link below.
Note that to generate split rails like in an audio amplifier, you need two Ideal Bridge Rectifiers and a transformer with two separate secondary windings (not a common centre tap connection).
The photo shows the fully-assembled module.
|
 |
Ideal Bridge Rectifier kit, standalone D2PAK SMD version
A complete kit to build one Ideal Bridge Rectifier in the standalone SMD D2PAK form factor with screw terminal connectors.
For a complete list of parts in the kit, see the link below.
Note that to generate split rails like in an audio amplifier, you need two Ideal Bridge Rectifiers and a transformer with two separate secondary windings (not a common centre tap connection).
The photo shows the fully-assembled module.
|
 |
Ideal Bridge Rectifier kit, standalone TO-220 through-hole version
A complete kit to build one Ideal Bridge Rectifier in the standalone through-hole TO-220 form factor with spade connectors.
This version can handle the most current out of any of the Ideal Rectifiers and includes a PCB with double-thickness (70µm/2oz) copper.
For a complete list of parts in the kit, see the link below.
Note that to generate split rails like in an audio amplifier, you need two Ideal Bridge Rectifiers and a transformer with two separate secondary windings (not a common centre tap connection).
The photo shows the fully-assembled module.
|
 |
Coin Cell Emulator kit
A kit that includes all the parts needed to build the Coin Cell Emulator. It has the PCB and all onboard parts - see the link immediately below for a full list.
Note: the photo shows the fully assembled kit.
|
 |
Short-form kit for the Pico Audio Analyser
A kit that includes most parts needed to build the Pico Audio Analyser. It has the PCB and all onboard parts - see the link immediately below for a full list.
It does not include the case, battery holder, battery, chassis connectors or wiring.
The Raspberry Pi Pico is included but not programmed. You can easily program it yourself using a computer, the free software download from our website and a suitable USB cable.
Note: the photo shows the fully assembled device including the parts not included in the kit.
|
 |
K-Type Thermocouple Thermometer/Thermostat short-form kit
A kit that includes most of the parts you need to build the Thermometer/Thermostat. Click the link immediately below to see a list of everything that's included in the kit.
What isn't included: the case, LCD screen, thermocouple probe or cable gland. Pretty much everything else is included.
Note: the photo shows the assembled kit, including some parts that must be purchased separately.
|
 |
Modem/Router Watchdog kit
A basically complete kit for the Modem/ Watchdog. It includes everything you need to build the Watchdog, assuming the rectified supply voltage is close to 12V DC.
If your voltage is significantly different from that, you might need to substitute the relay or add a resistor.
The Raspberry Pi Pico W is included but is not programmed; you can program itself using a computer, the free software downloaded from our website and a suitable USB cable.
Note: the photo shows the assembled kit.
|
 |
PIC Programming Adaptor kit
A complete kit for the new PIC Programming Adaptor. It includes the PCB, ZIF socket, Raspberry Pi Pico and all other parts to build the board as shown in the magazine.
You just need to add a PICkit or SNAP programmer. See the link immediately below for a complete list of the parts included.
Note: photo shows assembled kit. Some components may have a slightly different appearance.
|
 |
Small Dynamic RFID Tag kit
A small kit that includes the small purple Tag PCB, the RFID chip and the three extra passive components.
Note: photo shows assembled tag.
|
 |
Credit card size Dynamic RFID Tag kit
A small kit that includes the larger black Tag PCB, the RFID chip and the three extra passive components.
Note: photo shows assembled tag.
|
 |
Short-form kit for the Reciprocal Frequency Counter
A small kit for the Reciprocal Frequency Counter that includes everything except the case and TCXO.
See the link immediately below for a full list of parts included in the kit.
Note: photo shows assembled prototype PCB including some parts that are not included in the kit (primarily the oscillator module).
|
 |
Basic RF Signal Generator short-form kit
A mostly-complete kit for the AD9834-based RF Signal Generator. Click the link below to see what's included in the kit.
Besides this kit, you just need the case, the AA cells and the optional output level adjustment pot (if you plan to fit it).
Note: the photo shows the assembled board. Some parts may have a different appearance than those shown.
|
 |
Wideband Fuel Mixture Display short-form kit
A set of parts for the WFMD, which includes the PCB and all the onboard parts. You will need to purchase the O2 sensor, connectors, case, wiring, pressure sensor and some other bits and pieces separately.
Click the link immediately below to see a full list of all parts included in the kit. Note: photo shows assembled PCB with wiring in place.
|
 |
Short form kit for the Dual RF Amplifier
A kit for the Dual RF Amp that includes the PCB and everything that mounts on it. What is not included is a case, power supply etc. Click the link below for a full list of what's included in the kit.
Note: photo shows kit after assembly.
|
 |
Songbird kit
A kit that includes pretty much everything you need to build the Songbird (click the link below for a full list of parts).
The only parts not included are the base and some AA cells. The kit includes the PCB, the parts that mount on the PCB, the piezo speaker, 3D-printed speaker surround and switched battery box with wire leads.
Note: photo shows the Songbird assembled using a separate battery holder and switch (holder with integrated switch included in kit). Base not included in kit. Some parts supplied may differ in appearance.
|
 |
Testbench Swiss Army Knife short form kit
A kit for the Automated Test Bench that includes the PCB, all SMDs, the boost module, the SIP reed relay and the laser-cut lid. Click the link immediately below for a full list of all parts.
Note: photo shows assembled prototype PCB.
|
 |
Silicon Chirp kit
A complete kit for Silicon Chirp. All you need to add is the CR2032 lithium coin cell.
Note that due to the way programming works and how sound selection works, it's possible that the chip will start up in Frog or Canary mode rather than the default (Cricket). See the instructions in the article for how to change it back to Cricket if that happens.
Also note that the photo show the kit after assembly.
|
 |
Digital Potentiometer kit (SMD version)
A kit that includes the PCB for the SMD version of the Digital Volume Control Potentiometer plus all the non-optional parts that mount on it. See the link below for a complete list of parts included.
Note: photo shows assembled kit. Some components may look different.
|
 |
Digital Potentiometer kit (through-hole version)
A kit that includes the PCB for the through-hole version of the Digital Volume Control Potentiometer plus all the non-optional parts that mount on it. See the link below for a complete list of parts included.
Note: photo shows assembled kit. Some components may look different.
|
 |
Hard-to-get parts for the Active Mains Soft Starter
A set of parts for the Active Mains Soft Starter. It is not a complete set but once you have these parts, you should be able to get the rest from Jaycar and/or Altronics.
See the link immediately below for a list of all the parts included. All semiconductors are in the set, including the programmed microcontroller, plus the relay, transformer and NTC thermistor.
Note: the photo shows the fully assembled PCB, including parts not in this set.
|
 |
Advanced SMD Test Tweezers kit
A set of all the parts needed to build the SMD Test Tweezers. All you need to add is a CR2032 lithium coin cell.
For a complete list of all parts in the kit, see the link immediately below. The programming header is not included because the supplied chip is pre-programmed.
Note: the photo shows the fully assembled Tweezers.
|
 |
Q Meter short-form kit
A set of all the parts to build the Q Meter apart from the case, power supply and wiring.
Click the link immediately below for a list of all the parts in the kit.
The photo shows the PCB after assembly.
|
 |
Raspberry Pi Pico W BackPack kit
A kit of all the parts needed to build the Raspberry Pi Pico W BackPack module, including the PCB and all the optional components except for the DS3231 real-time clock IC (available separately). See the link below for a full list of parts included in the kit.
This kit also includes four 1mm-thick Nylon washers, and four of the eight M3 screws are 8mm long, so you can either build it as a standalone module or mount it to a panel. That includes mounting it in a UB3 Jiffy box using our laser-cut acrylic lid (also sold separately, see below).
Note: photo shows the assembled Pico W BackPack module with the optional RTCC IC fitted.
|
 |
Micromite LCD BackPack V3 complete kit
A kit of all the non-optional parts required to build the Micromite LCD BackPack V3. See the parts list link below for details on what is included.
The PCBs, programmed microcontrollers and regulator are also available separately.
For assembly, set-up and operating instructions, see the article in the August 2019 issue.
Please note: software options which do not support the 3.5-inch touchscreen have been removed from the programming list as this was causing confusion.
|
 |
Complete kit for the Breadboard PSU
A set of all the parts needed to build the Breadboard PSU. This does not include the display portion; that is available as a separate kit.
Click the link below to see a list of all the parts included. Note: the photo shows the kit after assembly.
|
 |
Complete kit for the Breadboard PSU Display
A set of all the parts needed to build the Breadboard PSU panel meter that shows the voltages, currents etc. You will also need the base Breadboard PSU that is available as a separate kit.
Click the link below to see a list of all the parts included. Note: the photo shows both kits assembled together.
|
 |
Complete Kit for the Digital Boost Regulator/Breakout Board
A set of all the parts needed to build the Digital Boost Regulator, including a pre-programmed chip.
Click the link below to see a list of all the parts included. Note: the photo shows the kit after assembly.
|
 |
Hard-to-get parts for the Hummingbird Amplifier
A small set of parts for the Hummingbird Amplifier which constructors might find difficult to obtain otherwise.
The set includes two driver transistors (MJE15034G & MJE15035G), a VAS transistor (KSC3503DS), a 220pF 250V C0G ceramic capacitor and two 0.22Ω 5W resistors of the type specified in the parts list.
The PCB is available for purchase separately on our website. The remainder of the components can be obtained from a retailer like Jaycar, including the MJL21193 & MJL21194 power transistors.
Keep in mind that Altronics have a complete kit for this module (Cat K5158).
Note: photo shows fully assembled module, including parts not included in this set.
|
 |
Short-form kit for the LC Meter Mk3
A kit that includes the PCB for the LC Meter Mk3 and all the parts that mount on it, plus the battery holder. You just need to add the case, front panel label and AA cells. The Arduino Nano is not programmed.
Check the parts list link below for the full details. The photo shows the kit after assembly.
|
 |
Kit for the new GPS Analog Clock Driver
A complete kit for the New GPS-Synchronised Analog Clock Driver including the VK2828 GPS module, PCB and all onboard parts - everything in the Parts List published in September 2022 plus some double-sided tape to hold down the GPS module.
This kit is for the AA-powered version; if you want to power it with larger cells, you will need to add your own cell holders, wiring and possibly a connector.
The photo shows the kit after assembly with two AA cells installed (not included).
Note: the D1 Mini version of the kit is no longer available due to Windows serial driver problems - see the separate shop item, SC6929.
Kits sold from now on use the v1.2 firmware that provides multiple pulse width options for sweep hand movements.
|
|
Kit for the new GPS Analog Clock Driver without GPS module
A complete kit for the New GPS-Synchronised Analog Clock Driver without the GPS module. It includes the PCB and all other onboard parts - everything in the Parts List published in September 2022 except the GPS module.
This kit is for the AA-powered version; if you want to power it with larger cells, you will need to add your own cell holders, wiring and possibly a connector.
The photo shows the kit after assembly with the added GPS module and two AA cells installed (not included).
Note: the D1 Mini version of the kit is no longer available due to Windows serial driver problems.
Kits sold from now on use the v1.2 firmware that provides multiple pulse width options for sweep hand movements.
|
 |
Tiny LED Christmas Ornament complete kit
A kit with all non-optional parts for one of LED Christmas Ornaments, including the chosen PCB and programmed micro. The kit includes 12 green*, white* and red* LEDs so you can mix and match what colours you like. You just need to select what PCB you want with your kit from the drop-down menu labelled "Type".
To order multiple different types, select one type and quantity and add them to your trolley, then repeat with the next type and quantity etc.
*the Icicle comes with white, blue & cyan LEDs instead to better match its appearance
|
 |
Complete kit for the Buck/Boost Charger Adaptor
A kit that includes everything in the parts list for the Multi-Stage Buck-Boost Charger Adaptor except the LED Driver Module (available as a separate kit).
The PCB, laser-cut clear acrylic cover and microcontroller are included. The micro is pre-programmed.
Note: photo shows the assembled kit before the OLED screen is installed.
|
 |
Hard-to-get parts for the WiFi Controlled DC Electronic Load
A set of some of the difficult-to-get parts for the WiFi DC Electronic Load project which includes all the SMDs plus quite a few other semiconductors. Check the parts list link below for details.
This set includes the parts for the main PCB, daughter PCB and control PCB. But note that it is not an exhaustive set and you will need to add some 'regular' parts to complete the board assemblies.
|
 |
Complete kit for the High Power Buck-Boost LED Driver
A kit including the PCB and all the onboard parts to build the High Power Buck/Boost LED Driver.
It includes the four diodes and two inductors needed to build the full-power version.
The kit does not include an LED panel. Those are available separately in two versions (warm white or cool white) - see the links immediately below.
Note: photo shows fully assembled PCB.
|
 |
Complete kit for the Mini LED Driver
A kit that includes everything you need to build the Mini LED driver described in the September 2022 issue.
That means the PCB, boost module and all the parts that fit on the PCB; ie, everything in the published Parts List.
Note: photo shows kit after assembly. Some components may look slightly different.
|
 |
Partial kit for the Wide-Range Ohmmeter
A set including the PCB, all SMDs and some other parts needed to build the Wide Range Ohmmeter.
See the parts list link below for details on what is included.
You will need to separately source the case, LCD (available from our shop), battery holder, relays, and some other standard through-hole parts like resistors, electrolytic capacitors, diodes and transistors. None of those parts should be too hard to find.
Note: photo shows assembled PCB including parts not included in this set.
|
 |
Complete kit for the Multimeter Checker
A set of all the parts specified in the parts list of the Multimeter Checker project, including the PCB and all onboard parts.
The microcontroller is supplied pre-programmed. SMD LEDs are included as they are a better match the other components, which are mostly surface-mounted.
Note: photo shows fully assembled kit.
|
 |
VGA PicoMite short-form kit
A set of parts to build the VGA PicoMite witnout a case. The Raspberry Pi Pico is supplied pre-programmed and tapped spacers are included to use as feet. Headers and sockets are also supplied to make the Pico pluggable.
You will need to add a power supply, keyboard, monitor and optionally an SD card (or micro SD card with full-size adaptor).
The I/O header supplied is the standard vertical type. If you want to build it into a case, you will need the case, a 40-pin right-angle box header and four No.4 x 5mm self-tapping screws.
Note: photo shows assembled kit with green PCB (blue supplied).
|
 |
Short-form kit for the 0-110dB RF Attenuator
A kit for the 0-110dB Attenuator which includes the PCB, programmed microcontroller and all the other components that mount on the PCB.
All you need to add is the case, panel label, power supply, chassis-mounting DC socket(s), chassis-mounting power switch and the off-board wiring.
Note: photo shows the assembled PCB mounted in the case with off-board components that are not included in the kit.
|
 |
Short form kit for the Spectral Sound MIDI Synthesiser
A kit with the PCB and all other electronic components for building the Spectral Sound MIDI Synthesiser. All eight PICs are included and come pre-programmed, along with sockets for them and most of the other ICs.
The only items listed in the parts list for this project not included in the kit are the power supply, case, feet for the case and labels.
Update 26/06/2023: kits sent from now on will have the updated firmware loaded: Master Controller V2, Mixer V2, Tone Processor V8.
|
 |
Hard-to-get parts for the 500W Amplifier
A set of all the critical parts needed to build the 500W Amplifier (not including the PCB, which is sold separately).
See the parts list link below for details on what is included.
All the rest of the parts (mainly resistors, capacitors, connectors and heatsinks) are available from your usual parts supplier like Altronics or Jaycar.
Note: photo shows the fully assembled amplifier module, including parts not in this set.
|
|
Parts collection for the 500W Amplifier
A collection of various items we sell to help build the complete 500W amplifier.
This does not include all required parts but does have everything we sell that's relevant, ie:
- The 500W amplifier module PCB.
- Our set of hard-to-get parts for the 500W amplifier module, including most of the semiconductors.
- The Clipping Indicator PCB.
- The Fan Controller/Speaker Protector PCB and programmed microcontroller, plus three 4-pin PWM fan headers.
Click the link immediately below for a full list of parts included in this collection.
Note: photo shows the fully assembled amplifier module, including parts not in this set.
|
 |
Micromite Plus LCD BackPack kit without touchscreen
A kit of all the parts required to build the Micromite Plus LCD BackPack, except the touchscreen. Useful for the Slot Machine project as it requires a different screen than we usually use.
See the parts list link below for details on what is included.
The PCBs and programmed microcontroller are also available separately. The photo shows the assembled module with a micro SD card (not included).
|
 |
Hard-to-get parts & PCB for the Capacitor Discharge Welder Energy Storage Module (ESM)
A set of hard-to-get parts to build one CD Welder ESM; see the parts list link below for details on what is included.
To make a complete ESM, you need to add the electrolytic capacitors, the connectors, the LED and the through-hole resistor.
Notes:
1) You will need multiple sets of these parts - between 8 and 14 (see the articles). You will also need the Power Supply (partial kit available separately), Controller (PCB available separately) and sundry other parts, as detailed in the articles.
2) The Mosfet driver has an exposed pad on the bottom (matching a pad on the PCB) but this does not need to be soldered. The ground connection is via one of the external pins and it does not need extra heatsinking.
3) The photo shows the fully assembled module, including parts not included in this kit.
|
 |
Hard-to-get parts & PCB for the Capacitor Discharge Welder Power Supply
A set of hard-to-get parts to help build one CD Welder power supply; see the parts list link below for details on what is included.
To complete the board, you need to add quite a few 'standard' parts like resistors, capacitors etc. See the article parts list for details.
Notes:
1) You will need multiple ESM modules (partial kit available separately), the Controller (PCB available separately) and sundry other parts, as detailed in the articles.
2) The photo shows the fully assembled module, including parts not included in this kit.
|
 |
Improved SMD Test Tweezers kit
A kit of parts to build the SMD Test Tweezers. The updated version from the April 2022 issue replaces the pre-existing kit as it does everything the earlier one did and more.
It includes the PCB, programmed microcontroller, other onboard parts, heatshrink tubing and gold-plated header pins for the tips.
This kit does not include the lithium button cell. The photo shows what it looks like after assembly.
If you would prefer the pre-made tweezer 'hands' as pictured on page 69 of the original (October 2021) article, these can be purchased from Altronics, part #: P0417.
|
 |
Raspberry Pi Pico BackPack kit
A kit of all the parts needed to build the Raspberry Pi Pico BackPack module, including the PCB and all the optional components except for the DS3231 real-time clock IC (available separately).
This kit also includes four 1mm-thick Nylon washers, and four of the eight M3 screws are 8mm long, so you can either build it as a standalone module or mount it to a panel. That includes mounting it in a UB3 Jiffy box using our laser-cut acrylic lid (also sold separately, see below).
Note: photo shows the assembled Pico BackPack module with the optional RTCC IC fitted.
|
 |
Hard-to-get parts for the Intelligent Dual Hybrid Power Supply regulator board
A partial set of parts to build one regulator board for this project. See the parts list link below for details on what is included.
The PCB is not included but we can supply it separately or as part of a PCB set. The rest of the parts needed to build the regulator module are readily available.
The LM2575 regulator is not included in this kit; as only one is needed per device, it is included in the CPU board parts set (or get it from Altronics).
Two of these parts sets are needed to build the dual version of the supply.
Note: Image shows assembled regulator board.
|
 |
Hard-to-get parts for the Intelligent Dual Hybrid Power Supply CPU board
A partial set of parts to build the CPU/control board for this project. See the parts list link below for details on what is included.
The PCB is not included but it is available from us separately or as part of a set. The LM2575 regulator mounts on one of the regulator boards, but as only one is needed per device, it is included in this set of parts.
The rest of the parts needed to build the CPU module are readily available.
Note: Image shows assembled CPU board.
|
 |
Kit for the Remote Control Range Extender IR-to-UHF adaptor
A kit of all the parts needed to build the mini PCB module for the Remote Control Range Extender UHF transmitter.
The kit includes the PCB, programmed microcontroller and all other onboard components including the optional pull-up resistor. It does not include any wiring.
Keep in mind that this kit includes parts as small as 0.6 x 0.3mm so it requires advance soldering skills and/or tools.
Note: the photo shows the fully assembled module.
|
 |
Kit for the SMD trainer
A kit to build the SMD trainer board with everything except the coin cell (CR2032 type), which is widely available.
It includes the PCB and all onboard parts, with spares for the really tiny components (four each of the M1005/0402 and M0603/0201 parts when only two are required).
Note: photo shows PCB after assembly.
|
 |
Short form kit for the USB Cable Tester
A kit that includes all the parts to build the USB Cable Tester as presented in the magazine, except for the plastic instrument case (available from Altronics & Jaycar; see the article for part numbers).
See the parts list link below for details on what is included.
No AA cells are included. Apart from those and the case, you get everything you need to build a fully working USB Cable Tester.
Note: photo shows assembled PCB without LCD screen or bezel.
|
 |
Hard-to-get parts for the Flexible Digital Lighting Controller
A set of some of the parts for the Digital Lighting Controller (October & November 2020). See the parts list link below for details on what is included.
If you order this set of parts, the two PCBs and the programmed microcontroller from us, you should be able to get the remainder of the parts from Altronics and/or Jaycar.
Note: photo shows assembled unit.
|
 |
Hard-to-get parts for the Model Railway Carriage Lights
A set of parts which includes the PCB and all SMDs for the Model Railway Carriage Lights project. See the parts list link below for details on what is included.
The LEDs, reed switch, magnet, zener diode and through-hole capacitors are all available from retailers like Jaycar & Altronics.
Note: Assembled prototype PCB shown. The supplied PCB will have a green solder mask.
|
 |
Micromite LCD BackPack V2 complete kit
A kit of all the parts required to build the revised version of the Micromite LCD BackPack. See the parts list link below for details on what is included.
PLEASE NOTE: the 10µF capacitors supplied are either non-polarised SMD or through-hole ceramic types. They have no markings and can be installed either way around.
The PCBs, programmed microcontrollers and regulator are also available separately. For assembly instructions, see the article in the May 2017 issue.
| Programmed with: Lid colour: |
| Cat No SC4237. Price: AUD $70.00 1 |
 |
Add to trolley |
In stock:  yes (16 available). Estimated dispatch time: 1-3 days | | Related to:
|
| View 49 other items relevant to the same project(s) |
| Show kit parts list |
|
 |
Micromite LCD BackPack V1 complete kit
A kit of all the parts required to build the 2.8-inch version of the Micromite LCD BackPack. See the parts list link below for details on what is included.
The PCBs, programmed microcontroller and regulator are also available separately.
PLEASE NOTE: the 10µF and 47µF capacitors supplied are non-polarised SMD ceramic types. They have no markings and can be installed either way around. You can tell them apart as the 10µF capacitors are in a pack of two.
For assembly instructions, see the article in the February 2016 issue.
Also note: kits include 4 x 6mm machine screws, 4 x 10mm (or 8mm) machine screws and 4 x 3mm ID 6mm OD 1mm thick Nylon spacers. The longer screws & spacers are to attach the BackPack to the supplied lid. If not using the lid, place the washers under the 10mm screw heads.
| Programmed with: Lid colour: |
| Cat No SC3321. Price: AUD $65.00 1 |
|
Add to trolley (available until stock is exhausted) |
| In stock: yes (14 available). Estimated dispatch time: 1-3 days | | Related to:
|
| View 21 other items relevant to the same project(s) |
| Show kit parts list |
|
 |
Nano TV Pong short form kit
A small kit which includes the Nano TV Pong PCB, programmed microcontroller and all the other onboard SMD parts.
It does not include the controllers or wiring.
Note: photo shows assembled PCB.
|
 |
Hard-to-get parts for the Refined Full-Wave Motor Speed Controller
A set of parts for building the Refined Full-Wave Motor Speed Controller.
It includes the PCB, AX-1000 current transformer, programmed microcontroller and all other semiconductors.
The rest of the parts are available from Jaycar/Altronics. Note: photo shows assembled PCB, including parts not included in this kit.
|
 |
Complete kit for the Mini Isolated Serial Link
A set of all the parts needed to build the Mini Isolated Serial link including three different header options (straight, right-angle or socket strips). That includes the PCB itself and all onboard components.
Note: photo shows module after assembly, using socket strips.
|
 |
MiniHeart SMD parts
A set of all the SMD parts used in the MiniHeart. This does not include the PCB, programmed PIC or any of the through-hole parts.
|
 |
Kit for the RGB Stackable LED Christmas Star
A kit of all the non-optional parts for the RGB LED Star including the PCB, programmed microcontroller and 30 RGB LEDs.
The microcontroller programming includes a number of patterns designed specifically for the Star. The LEDs have diffused lenses for improved off-axis visibility.
Note: photo shows assembled kit.
|
 |
Mini WiFi LCD BackPack kit
A kit of parts for the D1 Mini LCD BackPack with WiFi. See the parts list link below for details on what is included.
The PCBs is also available separately. Note: photo shows assembled module without touchscreen.
For assembly, set-up and operating instructions, see the article in October 2020 issue.
|
 |
Hard-to-get parts for the High Power Ultrasonic Cleaner
A set which includes all the ETD29 transformer components (except the winding wire), plus the three Mosfets (Q1, Q2 & Q6) used in the High Power Ultrasonic Cleaner.
The PCBs, programmed microcontroller and ultrasonic transducer are available separately from our shop.
Please NOTE: Component substitution; the N-channel Mosfets (Q1, Q2) supplied may be CSD18534KCS devices, and the P-channel Mosfet (Q6) supplied may be a IPP80P03P4L-04 or -07 devices instead.
|
 |
Short-form kit for the Shirt Pocket Audio Oscillator
A kit of most of the parts needed to build the Shirt Pocket Audio Oscillator.
You just need to add some lengths of wire - no wire is included in the kit. Everything else you need is, including the knobs and battery clips.
Note: photo shows assembled prototype
|
 |
Kit for the Switchmode 78xx Regulator replacement
A kit with the PCB and all onboard parts for the Switchmode 78xx Regulator replacement project from August 2020.
The output voltage option determines what resistor and inductor values you get:
- 3.3V (31.6kΩ, 15µH)
- 5V (52.3kΩ, 22µH)
- 6V (64.9kΩ, 27µH)
- 8V (88.7kΩ, 39µH)
- 9V (102kΩ, 39µH)
- 12V (140kΩ, 56µH)
- 15V (178kΩ, 68µH)
Note: photo shows assembled module.
|
 |
Hard-to-get parts for the Thermal Regulator Peltier Driver shield
Some of the harder-to-get parts for the Peltier Driver shield. See the parts list link below for details on what is included.
|
 |
Hard-to-get parts for the DCC Power Shield
Two BTN8962TA half-bridge integrated motor driver ICs and one 6N137 opto-coupler, as used in the Arduino DCC project from the January 2020 issue.
The shield PCB is available separately. The rest of the parts can be purchased from just about any electronics retailer.
|
 |
Micromite Explore-28 complete kit
A kit of all the parts required to build the Micromite Explore-28 module. See the parts list link below for details on what is included.
The PCBs and programmed microcontrollers are also available separately.
Refer to the magazine issue listed below for assembly, set-up and operating instructions. Note that the photo shows the module after assembly.
|
 |
23LCV1024-I/P SRAM and MCP73831T charger IC for the 433MHz UHF Repeater
Two parts for the Solar-powered Data Repeater for 433MHz Remotes which are relatively difficult to obtain.
You can purchase the PCB and programmed microcontroller project separately from our Online Shop and the remaining parts are readily available from Jaycar and Altronics.
|
 |
Hard-to-get parts for the Touch and IR Remote Control Trailing Edge Dimmer
A pack with two 4.7MΩ VR37 high-voltage resistors and two SiHB15N60E-GE3 SMD Mosfets, as required for the Versatile Trailing Edge Dimmer with Touch and/or Infrared Remote Control.
The rest of the parts should be available from your normal electronics retailer(s), with the possible exception of the infrared remote receiver and fresnel lens. Those optional components are available in our shop as a separate item (Cat SC4862).
|
 |
Infrared receiver parts for the Touch and IR Remote Control Trailing Edge Dimmer
A pack with the TSOP4136 infrared receiver and IML-0688 Fresnel lens required to add infrared remote control to the Versatile Trailing Edge Dimmer with Touch and/or Infrared Remote Control.
|
 |
Short Form Kit for the Micromite Plus Explore 100
Kit of all parts to build the Micromite Plus Explore 100 EXCEPT for the screen and power supply.
Includes PCB and programmed microcontroller along with all other onboard parts (except for the optional ones) and mounting hardware, besides the TFT touchscreen.
For assembly instructions, see the article in the October 2016 issue.
The optional Real-Time Clock module and USB/serial converter module are available separately from our shop.
|
 |
Short form kit for the Motion-Triggered 12V Switch
Includes the PCB and all onboard parts.
|
 |
Kit for the Super Digital Sound Effects Module
A kit of parts for the Super Digital SFX Module in the August 2018 issue. For assembly instructions, see the article in the September 2018 issue.
The kit includes the PCB and all of the onboard parts, except for some optional ones. See the parts list link below for details on what is included.
It does not include a microSD card or any sort of battery holder, speaker, wiring or power supply. You will need to purchase those separately.
Note: photo shows module after assembly and with microSD card inserted (not included).
|
 |
Kit for the Stackable LED Christmas Tree
A kit of parts to build a single board for the Expandable Christmas Tree. Includes the PCB, IC, capacitor, resistors, high-brightness LEDs (three green, three red and three white) and connectors.
As well as the specified 1kΩ resistors, we are including 820Ω and 220Ω resistors. These can be used with the white and red LEDs respectively, to better match their brightness to the green LEDs.
Refer to the November 2018 issue for assembly, set-up and operating instructions. The Digital Interface Module in the same issue can be used to drive the Tree (http://www.siliconchip.com.au/Shop/20/4750).
You will get a discount if you order more than one. Price breaks are at four ($32 total), 18 ($126), 31 ($199) and 38 ($229).
Note: photo shows assembled kit.
|
 |
Kit for the Digital Interface Module
A kit of parts to build the Digital Interface Module, as used to drive the Stackable Christmas Tree. Includes the PCB, programmed micro, capacitors, resistor and connectors.
Refer to the November 2018 issue for assembly, set-up and operating instructions.
Note: photo shows assembled kit.
|
 |
Hard-to-get parts for the Tinnitus/Insomnia Killer
Two of the harder to get parts for the Insomnia and Tinnitus Killer project.
You get one LF50CV regulator in a through-hole TO-220 package and one LM4865MX audio amplifier IC in a surface-mounting SOIC 8-pin package.
You will also need to purchase the appropriate PCB to suit the case that you plan to use.
The remaining parts are available from Jaycar and/or Altronics - see the parts list in the November 2018 article.
|
 |
SMD parts for the GPS-Synched Frequency Reference
A set of some of the parts for the GPS-Synched Frequency Reference project; see the parts list link below for details on what is included.
This kit does not include any connectors, any other through-hole parts or the LCD BackPack module. We have a separate LCD BackPack kit available, with the PIC pre-programmed with the software for this project.
If you order this set of parts, plus the BackPack kit, you will still need to purchase the box, power supply, a suitable GPS module, the connectors and a few through-hole parts separately to complete the unit.
Assembly instructions are in the October and November 2018 issues.
Note that the photo shows an assembled board, including the extra through-hole parts which are not included in this parts set.
|
 |
Complete kit for the USB Port Protector
This kit includes the PCB and all parts for the USB Port Protector, plus a length of heatshrink tubing to protect it.
For assembly instructions, see the article in the May 2018 issue.
Note: photo shows kit after it has been assembled.
|
|
SMD parts for the 3-way Adjustable Active Stereo Crossover
A set of all the SMD parts for the 3-Way Active Crossover. See the parts list link below for details on what is included.
We have a pack of 8-gang potentiometers and knobs available separately, as well as the PCB, front and rear panels and case pieces. All the other parts should be available from local retailers.
Refer to the magazine issues listed below for assembly, set-up and operating instructions.
|
 |
Microbridge complete kit
A kit of all the parts required to build the Microbridge. See the parts list link below for details on what is included.
The PCB, programmed microcontroller and regulator are also available separately.
For assembly instructions, see the article in the May 2017 issue.
PLEASE NOTE: the 10µF capacitors supplied are non-polarised SMD ceramic types. They have no markings and can be installed either way around.
|
 |
Hard-to-get parts for the Electronic Fuse
Two NIS5112D1R2G electronic fuse ICs (SMD) plus one SUP53P06 P-channel Mosfet, as used in the regular eFuse project.
Note: the P-channel Mosfet (Q1) supplied may be a compatible IPP80P03P4L-04 or -07 device instead.
|
 |
Hard-to-get parts for the LED Pool Lap Counter
Two 70mm blue 7-segment displays (common anode) plus CSD18534KCS logic level Mosfet (TO-220).
|
 |
Hard-to-get parts for the Stationmaster
DRV8871 IC (SOIC-8), SMD 1uF capacitor and 16mm 100k linear potentiometer with centre detent.
|
 |
Hard-to-get parts for the SC200 Audio Amplifier Module
A set of the more difficult-to-get parts for the SC200 module. The PCB is sold separately and you can get the rest of the parts from Jaycar/Altronics.
See the parts list link below for details on what is included.
|
 |
Ultra Low Voltage Bright LED flasher kit
Kit for the Ultra Low Voltage Bright LED flasher. See the parts list link below for details on what is included.
For assembly instructions, see the article in the February 2017 issue.
|
 |
Hard-to-get parts for the High Power DC Motor Speed Controller
A set of the more difficult-to-get parts for the 60V/40A DC Motor Speed Controller. See the parts list link below for details on what is included.
The PCB and programmed microcontroller are sold separately and you can get the rest of the parts from Jaycar/Altronics.
|
|
Micromite LCD BackPack kit (programmed for Voltage/Current Reference)
THIS IS NOT A COMPLETE KIT FOR THE VOLTAGE/CURRENT REFERENCE.
A kit of all the parts required to build the 2.8-inch version of the Micromite LCD BackPack. See the parts list link below for details on what is included.
To build this project, you also need to either purchase the short form kit (available separately), which provides you with most of the remaining components, or the main PCB and acquire the remaining components elsewhere.
For assembly instructions, see the article in the February 2016 issue.
PLEASE NOTE: the 10µF and 47µF capacitors supplied are non-polarised SMD ceramic types. They have no markings and can be installed either way around. You can tell them apart as the 10µF capacitors are in a pack of two.
|
 |
Short Form Kit for the Touchscreen Voltage/Current Reference
Kit of all parts to build the Adjustable Voltage/Current Reference except for the BackPack module, case, power supply, PCB pins and wire.
Includes PCB and all other onboard parts, except for those listed above. For assembly instructions, see the article in the October 2016 issue.
The BackPack module with pre-programmed microcontroller is available separately, as is the laser-cut lid.
|
 |
SMD parts for Passive Line to Phono Input Converter
A set of the SMD parts required to build the Inverse RIAA project (Phono Input Converter), as described in the November 2016 issue.
Includes ten 10nF C0G SMD ceramic capacitors and six SMD resistors. The PCB and lid are available separately from our shop (see below) and you will also need to obtain the RCA connectors and box separately (eg, from Jaycar or Altronics).
|
 |
Micromite Plus LCD BackPack complete kit
A kit of all the parts required to build the Micromite Plus LCD BackPack. See the parts list link below for details on what is included.
The PCBs, programmed microcontroller and lid are also available separately.
For assembly instructions, see the article in the November 2016 issue.
The 6-8mm screws & Nylon washers are to attach the BackPack to the supplied lid. If not using the lid, place the washers under the screw heads.
|
|
Micromite LCD BackPack kit (programmed for Energy Meter)
THIS IS NOT A COMPLETE KIT FOR THE APPLIANCE ENERGY METER.
A kit of all the parts required to build the 2.8-inch version of the Micromite LCD BackPack. See the parts list link below for details on what is included.
Note: the lid is NOT included in this kit as it is a different size than the standard LCD BackPack and is available separately.
The PCBs (both for the Energy Meter and LCD BackPack), programmed microcontroller and regulator are also available separately. We can also supply a suitable real-time clock module although one is not included in this kit.
For assembly instructions, see the article in the February 2016 issue.
PLEASE NOTE: the 10µF and 47µF capacitors supplied are non-polarised SMD ceramic types. They have no markings and can be installed either way around. You can tell them apart as the 10µF capacitors are in a pack of two.
|
 |
Hard-to-get parts for the Currawong stereo valve amplifier
A small subset of the parts for the Currawong which are not available locally or are difficult to source. See the parts list link below for details on what is included.
The rest of the parts should be available from Jaycar and Altronics.
** The 9.1kΩ resistors were not originally included in the kit since 8.2kΩ can be used instead but we have decided to include them to offer constructors the choice.
|
 |
Micromite Plus Explore 64 kit
A kit of all the parts required to build the Micromite Plus Explore 64 module. See the parts list link below for details on what is included.
The PCB and programmed microcontroller are also available separately. For assembly instructions, see the article in the August 2016 issue.
|
 |
SMD components for the 100dB Stereo Audio Level Meter/VU Meter
A set of all the SMDs you need to build the Stereo Audio Level Meter, except for the programmed microcontroller and LEDs - both of which are available separately (see associated items).
See the parts list link below for details on what is included.
You will need to purchase the PCB separately. We can also supply the optional clear acrylic case pieces. The three through-hole connectors can be purchased from Jaycar, Altronics or just about any other electronics retailer. The pushbutton switches (S1 and S2) are from Jaycar.
|
 |
SMD resistors, capacitors and diodes for Arduino Multifunction Meter (MFM)
A set of all the SMD resistors, capacitors and diodes for the Arduino MFM project.
Includes the 0.1% resistors as well as 1% types, ceramic SMD capacitors, 3.9V 1W Zener diode and two 1N5711W-7-F Schottky diodes.
Note that this is not a complete kit and does not include the PCBs, ICs or any other parts not mentioned above. PCBs are available separately from our shop.
|
 |
Microwave Leakage Detector SMD parts
All the SMD parts needed to build the Microwave Leakage Detector. See the parts list link below for details on what is included.
The PCB is available separately. You will need to supply the cell holder, Lithium button cell, pushbutton and any other components.
|
 |
SMD Parts for the Battery Pack Cell Balancer
A complete set of SMD parts for the Battery Pack Cell Balancer. See the parts list link below for details on what is included.
The PCB is available separately.
Note: image shows completed unit which includes parts not in this pack. The programmed microcontroller is available separately.
|
 |
Hard-to-get parts for Stereo Valve Preamplifier
Some of the harder-to-get parts for the High-Performance Stereo Valve Amplifier. See the parts list link below for details on what is included.
The red & white RCA sockets and high-voltage Mosfets are also available separately from our shop; see below for details.
|
 |
SMD Parts for the Universal Speaker Protector, Mk3
All the SMD parts required to build the revised Universal Loudspeaker Protector module from the November 2015 issue.
See the parts list link below for details.
The PCB is available separately. Note that the through-hole components must be purchased separately (eg, from Jaycar and/or Altronics). Note that we do not supply the 220µF electrolytic capacitor.
Note: image shows completed unit which includes parts not in this pack.
|
 |
SMD parts for the Arduino-based USB Electrocardiogram
All the SMD parts required to build the Arduino USB ECG. See the parts list link below for details.
PCB is available separately. Note that the through-hole components must be purchased separately (eg, from Jaycar and/or Altronics).
|
 |
SMD parts for the Mini 12V USB Regulator with Low-Battery Cut-out
All the SMD parts required to build the switchmode regulator board from the article, "USB Charger Regulator With Low-Battery Cut-Out".
See the parts list link below for details.
PCB is available separately. Note that the (through-hole) connectors are not included as which ones you need depends on the application.
|
|
SMD parts for the Low-Cost, Accurate Voltage/Resistance/Current Reference (1.8V)
All SMD parts for the 1.8V version of the Voltage/Resistance/Current Reference. See the parts list link below for details on what is included.
The PCB is sold separately. The other parts such as the button cell holder are available from Jaycar and Altronics.
|
|
SMD parts for the Low-Cost, Accurate Voltage/Resistance/Current Reference (2.5V)
All SMD parts for the 2.5V version of the Voltage/Resistance/Current Reference. See the parts list link below for details on what is included.
The PCB is sold separately. The other parts such as the button cell holder are available from Jaycar and Altronics.
|
 |
SMD parts for the Mini 12V USB Regulator
All the SMD parts required to build the switchmode regulator board from the article, "Install USB Charging Points In Your Car".
See the parts list link below for details on what is included.
The PCB is available separately. Note that the (through-hole) connectors are not included as which ones you need depends on the application.
|
 |
Hard-to-get parts for the Balanced Input Attenuator
A pack of the harder-to-find parts for the Balanced Attenuator. See the parts list link below for details on what is included.
We sell the PCBs and panels for this project separately. The rest of the parts are available from Jaycar and/or Altronics.
|
 |
Hard-to-get parts for the Appliance Insulation Tester
A small pack of parts for the Appliance Insulation Tester; see the parts list link below for details on what is included.
We sell the PCBs separately. The rest of the parts are available from Jaycar and/or Altronics.
|
 |
Hard-to-get parts for the Isolated High-Voltage Probe
A set of parts for the Isolating High Voltage Probe project. Does not include the PCB. The remainder of the parts (standard resistors, capacitors, switches, etc) can be bought from the usual suppliers.
See the parts list link below for details on what is included.
|
 |
Hard-to-get parts for the Multispark CDI
A set of some of the parts for the new High-Energy Multi-Spark CDI (Capacitor Discharge Ignition) project. See the parts list link below for details on what is included.
We sell the PCB separately. The rest of the parts should be available from Jaycar/Altronics.
|
 |
SMD parts for the One-Chip 2 x 5W Mini Stereo Amplifier
A package which includes all the SMD parts for this project. See the parts list link below for details on what is included.
The PCB is available separately.
|
 |
Extra parts for the Dual-Channel Audio Delay / Stereo Echo & Reverb / Digital Effects Processor
WM8731SEDS CODEC IC (TSSOP-28) and SMD capacitors (11 x 100nF, 1 x 10µF). Can be put towards building the following projects:
- Stereo Audio Delay
- Stereo Echo & Reverberation Unit
- Digital Effects Processor for Guitars/Musical Instruments
The PCB and programmed microcontrollers (to suit the specific project) are also required and these are available separately.
|
 |
SMD parts for the 40V/5A Hybrid Switchmode/Linear Bench Supply
All the SMD parts for the Hybrid Bench Supply plus a couple of extra parts.
See the parts list link below for details on what is included. We sell the PCB separately.
|
 |
SMD parts for the RGB LED Strip Driver
All the SMD parts for the RGB LED Strip Driver/Controller, except the microcontroller which is available separately.
See the parts list link below for details on what is included.
The terminal blocks and other through-hole components you may require are available from various retailers including Jaycar and Altronics. We sell the PCB separately.
|
 |
Parts for the 10A 230VAC Universal Motor Speed Controller
The hard-to-get parts for the super-smooth motor speed controller. See the parts list link below for details on what is included.
The PCB and programmed microcontroller are available separately.
|
 |
SMD parts for SiDRADIO
A set of some of the more difficult-to-get components for the SiDRADIO project. See the parts list link below for details on what is included.
The double-sided PCB and front and rear panels are also available separately from our shop.
The rest of the parts are available from Jaycar and/or Altronics.
|
 |
Short form kit for the Battery Lifesaver
A kit which includes the PCB and all the SMD parts for the Battery Lifesaver project, including all the resistors you may need to set the required cut-off voltage. Does not include through-hole parts such as trimpot VR1 and zener diode ZD1.
For assembly instructions, see the article in the September 2013 issue.
|
 |
SMD parts for the RF Probe
A set of all the SMD parts for the RF Probe project. See the parts list link below for details on what is included.
The double-sided PCB is also available separately from our shop, with plated through-holes, silkscreen overlay and solder mask.
The rest of the parts are available from Jaycar and/or Altronics.
|
|
SMD parts for the LF-HF Up-converter
A set of some of the more difficult-to-get components for the LF-HF Upconverter project.
See the parts list link below for details on what is included.
The double-sided PCB is also available separately from our shop, with plated through-holes, silkscreen overlay and solder mask.
The rest of the parts are available from Jaycar and/or Altronics.
|
 |
SMD parts for the "Lump in Coax" mini mixer
A set of some of the more difficult-to-get components for the "Lump in Coax" battery-powered mixer project.
See the parts list link below for details on what is included.
The PCB is also available separately from our shop, with silkscreen overlay, solder mask, top layer links and routed corners.
The rest of the parts are available from Altronics
|
 |
SMD parts for the CLASSiC DAC
A set of some of the more difficult-to-get components for the CLASSiC DAC project. See the parts list link below for details on what is included.
Note that this does not include the microcontroller, which is available pre-programmed as a separate item in our shop.
The remaining components are available from Jaycar, Altronics and element14.
|
 |
Complete kit for the Champion+Pre-champion
A kit that includes all the parts needed to build the Champion and Pre-Champion, as described in the January 2013 issue. Click the link immediately below to see everything that's included in the kit.
The only parts you might need to add are some extra terminal blocks, screws, spacers etc if you decide to cut the board in half and use it as two separate boards.
Note: photo shows assembled kit. Some components may vary in appearance.
|
